发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

基于耦合声场建模的膨胀腔消声器声学性能分析及试验

针对圆柱形膨胀腔消声器三维建模及声学性能分析问题, 提出一种基于切比雪夫变分原理的耦合声场建模方法, 建立三维圆柱形膨胀腔消声器理论模型并搭建试验台架, 传递损失试验结果验证了理论模型的准确性. 将膨胀腔消声器内部声场分解为多个子声场, 基于子声场间压力与质点振速连续性条件, 推导声场耦合变分公式, 构建子声场拉格朗日泛函. 将子声场声压函数展开为切比雪夫-傅里叶级数形式, 通过瑞利-里兹法求解膨胀腔消声器频率、声压响应及传递损失. 计算并对比分析扩张比、扩张腔长度、进出口管偏置对膨胀腔消声器消声性能的影响. 结果表明: 扩张比增大会有效提高消声器在低频段的消声性能, 进出口管的偏置对消声器消声性能影响很小.     

从双层规划的角度看道德风险理论的一阶条件方法

本文首先对双层规划的一个特殊例子即道德风险模型中使用的一阶条件方法（FOA）做简要的梳理，然后提出一种更为一般的使FOA有效的原则与方法。新方法主要依赖于代理人对委托人设置的目标的最优反应映射是否存在不动点，这个性质不要求原问题与用一阶条件放松以后的问题之间的约束集等价，从而也不要求代理人的期望效用对行动具有全局凹性。在新方法下，可以用较为简单的方法证明FOA在以下两种情形之一有效，即如果分布函数是概率分布的凸组合或者分布函数来自某些特殊的指数族分布。     

Controlling thermomechanical behavior of semicrystalline hydrogenated polynorbornene through the cis- to trans-cyclopentylene ratio

Though polynorbornene synthesized by ring-opening metathesis polymerization has an intrinsically all-cis configuration of the cyclopentylene backbone rings, a fraction of these rings can be epimerized to the trans configuration during hydrogenation over suitable catalysts. By varying the method of hydrogenation, semicrystalline hydrogenated polynorbornenes (hPNs) with trans levels between 0 and 36% were obtained. With increasing trans content, the glass transition temperature, melting point, and enthalpy of melting decrease modestly. By contrast, the temperature at which the hPN crystal transitions into a rotationally disordered polymorph varies strongly with trans content, ranging from 126 °C (all-cis) to 71 °C at 27% trans; at trans contents of 34% and above, no rotationally-ordered phase is observed at any temperature. The room-temperature Young's modulus shows no dependence on trans content, while the yield stress drops by 20% at 1% trans content and slowly decreases further with additional epimerization. The temperature dependence of the Young's modulus differs for trans-containing versus all-cis polymers, while the temperature dependence of the yield stress is set by the polymorph type (rotationally ordered vs. disordered).     

Nonlinear elastic constitutive relations of residually stressed composites with stiff curved fibres

Applied Mathematics and Mechanics - Mechanical models of residually stressed fibre-reinforced solids, which do not resist bending, have been developed in the literature. However, in some residually...     

Pure annihilation decay of strange beauty meson into two charm heavy mesons

In this study, the heavy to heavy decay of \begin{document}$ B^0_s\rightarrow D^{*+}D^- $\end{document} is evaluated through the factorization approach by using the final state interaction as an effective correction. Under the factorization approach, this decay mode occurs only through the annihilation process, so a small amount is produced. Feynman's rules state that six meson pairs can be assumed for the intermediate states before the final meson pairs are produced. By taking into account the effects of twelve final state interaction diagrams in the calculations, a significant correction is obtained. These effects correct the value of the branching ratio obtained by the pure factorization approach from \begin{document}$ (2.41\pm1.37)\times10^{-5} $\end{document} to \begin{document}$ (8.27\pm2.23)\times10^{-5} $\end{document}. The value obtained for the branching ratio of the \begin{document}$ B^0_s\rightarrow D^{*+}D^- $\end{document} decay is consistent with the experimental results.     

新型暂堵酸化用自降解暂堵剂的制备及现场应用

针对传统暂堵酸化用暂堵剂颗粒耐酸性差、降解性差和除堵工艺复杂等问题，本研究通过水溶液自由基聚合法制备了一种新型的自降解暂堵剂CQZDJ。考察了单体加量、交联剂加量、引发剂加量对CQZDJ凝胶强度和降解性的影响；通过FT-IR、TGA、SEM对其结构进行表征；并对其降解机理进行了探讨；最后在长8区块的环平81-8实验井进行了现场实践。结果表明：CQZDJ凝胶强度及降解时间与单体加量、交联剂加量、引发剂加量成正比关系，且降解时间可控；降解性实验表明CQZDJ在(1%~10%)HCl溶液、水、（2%~10%）NaCl溶液中均可在4 d内完全降解，具备良好的降解性能，对地层伤害小；SEM照片显示CQZDJ的降解过程是从初始三维网状结构逐渐崩解为层状结构，最终降解为无规则线性小分子链的过程；暂堵后现场流压上升6.3 MPa，日产油由3.87 t/d增产至5.22 t/d，实现了储层的有效改造，增产效果显著。      

大尺寸电阻加热式碳化硅晶体生长热场设计与优化

大尺寸低缺陷碳化硅(SiC)单晶体是功率器件和射频(RF)器件的重要基础材料,物理气相传输(physical vapor transport, PVT)法是目前生长大尺寸SiC单晶体的主要方法。获得大尺寸高品质晶体的核心是通过调节组分、温度、压力实现气相组分在晶体生长界面均匀定向结晶,同时尽可能减小晶体的热应力。本文对电阻加热式8英寸(1英寸=2.54 cm)碳化硅大尺寸晶体生长系统展开热场设计研究。首先建立描述碳化硅原料受热分解热质输运及其多孔结构演变、系统热输运的物理和数学模型,进而使用数值模拟方法研究加热器位置、加热器功率和辐射孔径对温度分布的影响及其规律,并优化热场结构。数值模拟结果显示,通过优化散热孔形状、保温棉的结构等设计参数,电阻加热式大尺寸晶体生长系统在晶锭厚度变化、多孔介质原料消耗的情况下均能达到较低的晶体横向温度梯度和较高的纵向温度梯度。